A putter milled to your stroke, down to the degree.

Off the rack, most putters ship at a standard 34 or 35 inches and a lie of about 70 degrees. Your height and posture are not standard. We fit your putter to how you actually stand to the ball, then mill one that matches.

Find your fit → Open the 3D builder

$399 milled to order · one question here, the full fitting walkthrough takes about two minutes, no email required

Drag to spin · 303 stainless · milled to order

Customize this putter →

The real problem

The stroke is rarely the part that is broken.

You miss left, so you weaken your grip. You leave it short, so you hit the next one harder. The setup fights you because the putter was built for an average golfer who does not exist. Two numbers decide whether the putter helps you or works against you.

LengthSets where your eyes sit over the ball. Too long and you stand up off it and push putts right.

Lie angleDecides whether the sole sits flat at impact. Off by a couple of degrees, the heel or toe catches first and the face points a hair left or right.

How a build works

Four steps from your stroke to your putter.

Find your fit

Two minutes in the fitting walkthrough turns your height and posture into a starting spec: your length and your lie. Start it here.

Design it

Set the length, lie, alignment, insert, finish, engraving, and grip in the live 3D builder. The price updates as you go, so nothing is a surprise at checkout.

We mill it

Your spec goes to the shop. Your putter is built to your numbers, stamped with the spec, and hand finished before it ships.

Roll it

It arrives fit to the spec you approved. Take it to the green and the course, and keep rolling it past the point where you would normally trust a putter.

Fitting, step one

Find your fit.

Start with the question everything else hangs off. Answer it here and the full fitting walkthrough picks up from the next one, so nothing gets asked twice.

How tall are you?

Your shaft length

Length—

Length decides your posture, and posture decides everything else. Pick your height and the walkthrough takes it from there.

Start the fitting walkthrough →

Adjustable

One head, built properly, then set to you.

HandRight- or left-handed, built and fit the same way.Same price

LengthSet from your height so you stand to the ball instead of reaching for it.34″ or 35″

Lie angleSet to a starting point from your fit, then dialed in on a real stroke.68/70/72/74° or custom

AlignmentThe sightline your eyes actually trust, or none at all.4 options

Insert patternThe milling cut into the aluminum insert the ball meets.2 patterns

Insert colourBronze, gold, left bare, or a colour you specify.4 options

FinishBrushed, matte, polished, or gold, chosen for glare and feel.4 finishes

EngravingYour name, initials, a phrase, a signature, or your own artwork.+$50

GripStandard, or a custom spec with the colour, texture, and alignment you set.+$10

Questions

Before you build.

Can you fit me right without an in-person fitting?

The fitting walkthrough reads your length from your height and your starting lie from how you stand over the ball, and neither changes much once it is right. Lie is the one number that wants a real stroke, so the putter ships to your starting lie and gets adjusted once if the wear mark on the sole tells us to.

What does a custom putter cost?

Every putter is $399. Engraving adds $50 and a custom grip adds $10, so a build lands between $399 and $459. Length, lie, alignment, insert pattern, insert colour, and finish cost nothing extra. Start a build and the number updates as you set each option.

Do you build for left-handed golfers?

Yes. Pick Left in the builder. Left-handed putters are built and fit the same way as right-handed ones, at the same price.

How long does a build take?

Each putter is made to order, so it is not pulled off a shelf. Builds take four to six weeks from order confirmation, and we email your timeline after you order.

What if the fit is wrong when it arrives?

Roll it on real greens first. If the length or lie feels off, the wear pattern usually shows why, and a one-time adjustment brings it in. Email us your order number and we will work out what to change.